Anyway, that's not what this issue is about. It may not work on your system but Ill explain. the router is a Linksys WRT160NL and my current firmware is DD-WRT v24-sp2 (12/22/14). The router connected to the modem via it's WAN port and WAN port was NOT configured to be assigned to the router's LAN. My dd-wrt system is dd-wrt v24-sp2 (11/02/09) std (SVN revision 13064M VINT Eko). I have recently installed DD-WRT on my D-Link DIR-615 router (rev. Had Zyxel 660R in router mode but was tired of troubleshooting two devices. I have FTP (21) and HTTP (80) ports forwarded and those work fine. I actually tried putting the modem in bridged mode before (that time it still was a ZTE F660 cable modem) and it turned out that my DDWRT router would then assign IP adresses to neighbours that didn't pay their Internet bill and were cut-off by our ISP. Running DD-WRT v24-sp2 mini on an Asus WL-520GU.
With my router in the modem's DMZ, there shouldn't be any routing or natting issues, right? Egy repeater azért vezetéknélküli jelismétl, mert nem kell neki vezetékes net This video is about this wireless repeater to setup & review it works very well in my workshop 60 foot out side my house Check this Install DD - WRT on Linksys WRT54GL v1 Anytone AT-D878UV Firmware update v1 Download firmware android 2 WRT120N Firmware, WRT120N Setup Wizard WRT120N. I don't think this is a routing or natting issue. this one seems to have fallen off the radar, builds seem to fluctuate between no download data but CPU usage is OK (build 17924) to upload and download data but very high CPU usage. Why not put the modem in bridged more to avoid any routing or natting issues? Im using an E2000 with: DD-WRT v24-sp2 (09/09/11) std-usb-nas - build 17598M NEWD-2 K2.6 Eko comment:6 by porcupine, 10 years ago. If at that time I connect to the modem's Wi-Fi then the Internet connection is still ok and ping to 192.168.11.1 working To me that makes this a topic for the general forum, but since it has been moved from there, I hope someone in here is able to help meĬan you ping 192.168.11.1 after the Internet fails? The same issue that I have with my Broadcom Asus AC68U, I also have with my Atheros-based Netgear WNDR3700v1, as well as with my Qualcomm-based TP-Link Archer C7.
Youll find such information in the Manual of your. On the cable modem, I have placed 192.168.11.2 in the DMZ.ĭD-WRT v24-sp2 (12/22/14) std (SVN revision 25697) To get access to your Linksys DD-WRT-v24-SP2, you need the IP of your device, the username and password. The DCP3828S is configured to assign static IP address 192.168.11.2 to the AC68U's, which all works. Not sure if the connection type is relevant but the AC68U connects to the DCP3828S via Automatic Configuration via DHCP. Hence, my conclusion is that the AC68U is at fault. DD-WRT router is connected to your main home router via wi-fi or ethernet. DD-WRT router has already been hard reset (30/30/30 method) or restored to the factory defaults via the administration menu. When the WAN connection on the AC68U freezes, I can still access the Internet via the modem's WiFi. DD-WRT router has been flashed with the newest DD-WRT firmware (e.g. Local IP address of the modem is 192.168.11.1. My ISP has provided a Cisco DPC3828S DOCSIS cable modem with built-in router and WiFi Access Point. Let's go ahead and perform a few tests to ensure we haven't goofed up.You have not provided any information about your Internet Link.ĭo you use PPPoE for the Internet Connection? You have successfully enabled port forwarding on your Linksys DD-WRT-v24-SP2 Router. I disable the NTP and re enable it without success. Make sure “Enable” Checkbox is selected if available on your Linksys DD-WRT-v24-SP2 RouterĪnd that's it. Last modified 8 years ago 3591 closed ( duplicate ) X86 DD-WRT v24-sp2 (06/23/14) std - build 24461 Description ¶ Router not changing time when change the time zone.If you see a field called “External IP addresses“ enter 0.0.0.0 in it.Choose TCP / UDP on your Linksys DD-WRT-v24-SP2 Router.(Enter the same port if you don’t have a range) Enter the static ip address of the device that we created in step 3 of this guide.Application name / Description: Enter the name of the program.Click on "Add New" / "Create" buttons to create a new port forwarding rule on Linksys DD-WRT-v24-SP2 Router.5.Create port forwarding rule on your Linksys DD-WRT-v24-SP2 routerįollow the below steps, (the steps might slightly vary based on your model)